keronten.blogg.se - Rinnai energysaver 1004f blinking red light

RINNAI ENERGYSAVER 1004F BLINKING RED LIGHT MANUAL
RINNAI ENERGYSAVER 1004F BLINKING RED LIGHT CODE
RINNAI ENERGYSAVER 1004F BLINKING RED LIGHT SERIES

I have done a LOT of electrical circuit board repair and feel I could fix this if I could just get some information on the board and it's components. I would like to find if there was a schematic or component diagram for this board - as it looks VERY simple.

In any case, I pulled the unit out of the furnace and the cover off the motor controller - and I found a burned trace on the board. There are 2 different PN's on the unit 5SME44JG2006A (which I think is a GE part # AND HC23CE116 (which I think is a Carrier Part #) It is a GE motor that apparently has been discontinued - though it appears as though a replacement is available through Carrier. After running through a few tests, I determined that the ECM motor/control was bad.

RINNAI ENERGYSAVER 1004F BLINKING RED LIGHT CODE

I was not getting heat and saw the error code 4-2. I have a Carrier Model 58MVB with a bad inducer motor/controller assembly.

RINNAI ENERGYSAVER 1004F BLINKING RED LIGHT SERIES

I'm unsure of the model furnace I have (GUA Series Deluxe Energy Saver Forced Draft Upflow Gas Fired Furnace is the majority of the information I have :P), but I've looked for some basic trouble shooting information, and wouldn't mind some advice from another human. I've turned and left the unit off now, and am thinking of just calling a repair man, but I wouldn't mind a) understanding a bit more about what's going on, and b) know if it's something I can personally fix, relatively easily. Flames in the lower chamber, and a couple clicks, a little heat, then nothing. I see the flames in the burner chamber (? forgive my lack of knowledge about my furnace, this is the first time I've every dealt with one personally), I hear some clicks, which I assume is the ignition sequence, and I feel a little bit of heat going through the ducts, but it quickly fades and it attempts the ignition sequence again. Where, before it, would work after a reset, it now seems that the ignition sequence is not being completed. So, I go to give this a try, and the furnace is no longer working at all now. So now I clutter your forum with it's own separate post. I apologize for posting on an old post, but thought perhaps I might get the attention of people who seemed knowledgeable about my situation without much hassle. I'm more than likely going to give the wiring a test as was mentioned earlier, but I thought I'd ask here first and see if what I'm describing might indicate a faulty unit or faulty wiring before even going out and getting a volt meter or anything like that. No blinky light and it went back to heating the house, but now, it will randomly stop heating again (still going, but not actually providing any heat) until I turn it on and off again. After the unit started up again, everything was fine.

RINNAI ENERGYSAVER 1004F BLINKING RED LIGHT MANUAL

I noticed my 50E47-140 W-R had it's red light blinking, but I don't have the repair manual and I'm not entirely sure where to get it, so before calling anyone about it, I tried simply "turning it off and turning it on again". Due to the modern designs of engineers, Rinnai EnergySaver has low sound effects and safety features like sealed combustion and a cool-touch cabinet. It is available for propane or Rinnai gasoline which offers a lot of warmth for a small price.

For superseded products please contact Rinnai to confirm product information.My furnace stopped working, so I popped off the cover and took a look around. Rinnai EnergySaver can be installed almost anywhere in your house to supplement existing heating systems. This information may be different for superseded products. The product information on this website (comprising product brochures, warranty information, installation manuals, diagrams, specifications and representations) relates to current products.

Economy mode – allows the heater to modulate down one hour after the set temperature is reached, reducing running costs with no noticeable change in temperature.

Pre-heat mode – pre-heats the room up to 1 hour prior to set programmed time.

Dual digital timers – provide on and off programming for mornings and evenings.

Inbuilt humidifier tray – for greater comfort.

Power flue – allows for multiple installations.

Zero emissions – perfect for those with allergies or respiratory problems.

What’s more, its room sealed power flue system makes the 309FT ideal for bedrooms. The Energysaver 309FT is our smallest model, and thanks to its compact size it can fit into the tightest spaces.